Truck and Transport Heavy Equipment Mechanic Red Seal Exam
PACKAGE #1
- 750 Questions and Answers
- All Files Are PDF
PACKAGE #2
-
2000 Question and Answer
- All Files Are PDF
- Study Notes
- Books
- Critical Skills
- Corrects Repair Procedures
-
98% Of Students Pass With Work Experience
This exam prep Package is an essential tool for any Truck and Transport Heavy Equipment student preparing to write the Red Seal exam. Volvo truck manufacturing company and Kenworth manufacturing company. Each practice test closely imitates the Red Seal exam in content and level of difficulty.
A Truck and Coach Technician inspects, repairs and maintains commercial trucks, emergency vehicles, buses and road transport vehicles and performs work on structural, mechanical, electrical and electronic systems. Specifically, a Truck and Coach Technician inspects, repairs and maintains:
| Exam – Truck and Coach Technician – Ontario/Inter-Provincial | Score |
|
OCCUPATIONAL SKILLS |
8 |
|
ENGINE AND SUPPORTING SYSTEMS |
24 |
|
AIR SYSTEMS AND BRAKES |
23 |
| ELECTRICAL AND ELECTRONIC SYSTEMS | 25 |
|
DRIVE TRAIN |
19 |
| STEERING, CHASSIS/FRAMES, SUSPENSION, WHEELS, HUBS AND TIRES | 21 |
| CAB | 8 |
| TRAILERS | 6 |
| CLIMATE CONTROL | 8 |
| HYDRAULIC SYSTEMS | 8 |
Truck and Coach Technician
A Truck and Coach Technician apprenticeship involves practical training provided on-the-job by a skilled worker or trainer.
The skills or competencies to be developed through this training In Ontario this trade is compulsory, which means certification or registration as an apprentice is legally required to practice the trade.
Truck and Coach Technicians make around $68,000 per year, two years after being certified
The Truck and Coach Technician (310T) apprenticeship program consists of on-the-job and in-school training. The program typically takes three and a half years to complete and consists of:
- 6,000 hours of on-the-job training/work experience
- 720 hours of in-school training
A minimum of Grade 12 high school education or its equivalent is required to qualify for the Truck and Coach Technician apprenticeship program.
The Interprovincial Standards Red Seal Program is the nationally recognized standard for skilled trades workers in Canada. In Ontario, this trade is part of the Red Seal Program under the title Truck and Transport Mechanic.
Return Policy: All items are final sale, since these are digital products* Refunds are not granted because of purchase abused.
SAMPLE TEST QUESTIONS TRUCK AND TRANSPORT MECHANIC INTERPROVINCIAL RED SEAL EXAM
Section 1
OCCUPATIONAL SKILLS
1) In order to remove a power-drill-chuck, what direction is used?
A) Reverse rotation
B) Shunt wired
C) CW
D) CCW
Ans. C
Section 2
ENGINE AND SUPPORTING SYSTEMS
2) Upon cold start-up, a plume of “white” exhaust smoke exits the exhaust pipe. As the engine operates under load, the temperature gauge reading does not increase, and the volume of “white” smoke emitted, does not decrease. What is the most likely cause, as there is zero coolant loss?
A) The engine timing is excessively advanced.
B) The engine timing is excessively retarded.
C) The coolant thermostat is stuck in the open position.
D) An incorrect coolant-type was installed.
Ans. C
Section 10
HYDRAULIC SYSTEMS
3) A dump-box pulsates and produces a jerking-type of motion during lift cylinder extension. What could be the cause?
A) Worn-box-pivot bushings.
B) Reservoir over filled.
C) Restriction on the high-pressure side.
D) Worn pump.
Ans. D
Section 5
DRIVE TRAIN
4) When a hydraulic retarder is applied continuously at high speeds?
A) The engine overheats.
B) The hydraulic fluid overheats.
C) The transmission is overheated
D) The engine RPM exceeds suggested operational range.
Ans. B
Section 4
ELECTRICAL AND ELECTRONIC SYSTEMS
5) An operator downshifts to decelerate and the Jacob Engine Brakes are inoperative whenever the throttle pedal is released. What may be the problem?
A) Clutch switch.
B) TPS.
C) Nothing this is normal operating condition.
D) ABS is in failure mode.
Ans. A
Section 3
AIR SYSTEMS AND BRAKES
6) A new brake drum measures at 0.060in out-of-round. What is the correct procedure to follow?
A) Return as a defective casting.
B) Machine in order to provide a round surface.
C) Install in a hydraulic press in order to true the condition.
D) Install as-is because the heat of breaking will return it to shape.
Ans. A
Section 6
STEERING, CHASSIS/FRAMES, SUSPENSION, WHEELS HUBS AND TIRES
7) A technician is overhauling a 5th wheel, what components can be replaced?
A) King pin.
B) Jaws.
C) Slide bogie.
D) Bolster plate.
Ans. Is in the package
Buy Now: https://canadiantransportacademy.com/checkouts/cn/c1-4a4b22c2adf559970f8c8393359ee70c?ew_m=f
This section doesn’t currently include any content. Add content to this section using the sidebar.